Abstract:To investigate the collector discharge pressure fluctuation characteristics and the related factors in a 1 000 MW nuclear reactor coolant pump, steady and unsteady 3dimensional numerical simulation was conducted to depict the inner flow inherence and detailed pressure content of a domestic pump model. Both time and frequency domain analysis were further put forward. It is shown that reverse flow is one of the reasons that cause the pressure fluctuations at the joint of the collector and the discharge. Obvious pressure fluctuations exit at the collector discharge and the adjacent area. In addition, the more the operation condition deviates from the design point, the more severe the pressure fluctuations are. The fluctuation amplitude in the upper passage is higher than that in the lower passage. The mean amplitude are 11.5%, 9.62% and 13.78% respectively in the upper passage, while they are 13.62%, 12.53% and 15.79% respectively in the lower one under the flow rates of 0.9Q, 1.0Q, and 1.2Q. At the adjacent diffuser vanes, the fluctuation amplitude near both sides of the casing wall is larger than that near the midspan line. In the regions far from the diffuser outlet, the fluctuation amplitude is increased gradually from the top side wall of casing to the bottom one. The shaft rotating frequency is the major factor influencing pressure fluctuation at ever monitor point when the pump is working at the design point. However, both the shaft rotating frequency and the blade passing frequency are the main factors when it works at offdesign points.
[1]Rzentkowski G, Zbroja S. Acoustic characterization of a CANDU primary heat transport pump at the bladepassing frequency[J]. Nuclear Engineering Design, 2000, 196(1): 63-68.[2]In Soo Koo, Whan Woo Kim. The development of reactor coolant pump vibration monitoring and a diagnostic system in the nuclear power plant [J]. ISA Transactions, 2000,39(3): 309-316.[3]Kazem Farhadi, Anis Bousbiasalah, Fransceso D Auria. A model for the analysis of pump startup transients in Tehran research reactor[J]. Progress in Nuclear Energy, 2007, 49(7):499-510.[4]Martin W Trethewey, Joshua C Friell. A spectral simulation approach to evaluate probabilistic measurement precision of a reactor coolant pump torsional vibration shaft crack monitoring system[J].Journal of Sound and Vibration, 2008, 310(4/5):1036-1056.[5]马辉,周文建,闻邦椿. 核电站反应堆冷却剂泵的模态分析[J]. 机械制造,2006(10):14-17.Ma Hui, Zhou Wenjian, Wen Bangchun. Mode analusis of reactor coolant pump for nuclear power station.[J]. Machinery, 2006 (10):14-17.(in Chinese)[6]陈向阳,袁丹青, 杨敏官,等. 300 MW级核电站主泵压力脉动研究[J]. 核动力工程,2010,31(3): 78-82.Chen Xiangyang, Yuan Danqing, Yang Minguan, et al. Study on pressure fluctuation in main pump of 300 MW nuclear power plants[J]. Nuclear Power Engineering, 2010,31(3): 78-82. (in Chinese)[7]Muggli F A. CFD calculation of a mixed flow pump characteristic from shutoff to maximum flow[C]∥Proceedings of the ASME Fluids Engineering Division Summer Meeting,2003:249-254.[8]Untaroiu A, Throckmorton A L, Patel S M, et al. Numerical and experimental analysis of an axial flow left ventricular assist device:The influence of the diffuser on overall pump performance [J]. Artificial Organs, 2005,29(7):581-591.[9]唐红芬, 张梁,吴玉林. 双级轴流泵内部三维紊动流场CFD分析[J]. 工程热物理学报,2003,24(3):423-425.Tang Hongfen, Zhang Liang, Wu Yulin. Three dimensional numerical simulation of flow field inside a twostage axial pump[J]. Journal of Engineering Thermophysicl,2003, 24(3): 423-425. (in Chinese)[10]李颖, 周文霞, 张继革, 等. 核反应堆冷却剂循环泵全流道三维数值模拟及性能预估[J]. 原子能科学技术, 2009,43 (10):898-902.Li Ying, Zhou Wenxia, Zhang Jige, et al. Numerical simulation of threedimensional flow through full passage and performance prediction of nuclear reactor coolant pump[J].Atomic Energy Science and Technology,2009,43(10):898-902.(in Chinese)