Technology for 1 000 MW shaft sealed reactor coolant pump
FENG Xiaodong1, WU Dazhuan2, YANG Lifeng1, JIA Yun1
1.Harbin Electric Power Equipment Co. Ltd., Harbin, Heilongjiang 150066, China; 2.Institute of Process Equipment, Zhejiang University, Hangzhou, Zhejiang 310027, China
Abstract:As high-end equipment in pump industry, CNP1000 shaft sealed reactor coolant pump(RCP)in the primary loop system of pressurized water reactor(PWR)in a nuclear power plant is the only equipment which cannot be manufactured domestically. Therefore, the independent design, manufacturing and test of this kind of pump are important and difficult tasks in promoting the nationalization of nuclear technology in China. In the paper, the domestic technological situation and structural characteristics of 1 000 MW shaft sealed RCP are introduced briefly, and the design principle and technical implementation requirement are elaborated in terms of pressure retaining boundary, hydraulic components, pump rotor system, heat insulation subassembly, shaft seal, standstill seal, lower guide bearings, thrust bearing, integrated oil pump, oil seal, auxiliary system and key equipment in detail. Through an analysis on export restriction and application prospect of various types of RCP, it is shown that shaft sealed RCP has more strength in export and will occupy a dominant position in the nuclear equipment market for a long time. Presently, several key technologies, such as shaft seal, hydraulic components, full-load test and so on have been nationalized in a few domestic factories, but the theoretical principle of RCP is still not well established and needs to be explored further. Hence, as an important mission, the nationalization of RCP still requires a long time to be tackled.
[1]黄经国. 压水堆核电厂冷却剂主循环泵的技术历程和发展(Ⅰ)[J]. 水泵技术,2009(4):1-8. HUANG Jingguo. Technical route and development of coolant circulating pumps in PWR(pressurized water reactor)nuclear power station(Ⅰ)[J]. Pump technology, 2009(4): 1-8.(in Chinese)[2]黄经国. 压水堆核电厂冷却剂主循环泵的技术历程和发展(Ⅱ)[J]. 水泵技术,2009(5):1-7. HUANG Jingguo. Technical route and development of coolant circulating pumps in PWR(pressurized water reactor)nuclear power station(Ⅱ)[J]. Pump technology, 2009(5): 1-7.(in Chinese)[3]谢蓉,祁恒,单玉姣,等. AP1000核主泵模型泵导叶水力设计与数值优化[J]. 排灌机械工程学报,2014,32(12):1029-1034. XIE Rong, QI Heng, SHAN Yujiao, et al. Hydraulic design and numerical optimization of guide vane of AP1000 model nuclear main pump [J]. Journal of drainage and irrigation machinery engineering, 2014, 32(12): 1029-1034.(in Chinese)[4]王本振,王庆舟,徐洋洋. 压水堆核电站用轴封泵与屏蔽泵性能分析[C]//中国核科学技术进展报告(第三卷)——中国核学会2013学术年会论文集第10册. 北京:中国原子能出版社,2013:46-53.[5]美国机械工程师学会. ASME锅炉及压力容器规范国际性规范,NB分卷[S]. 北京:中国石化出版社,2004.[6]关醒凡.现代泵理论与设计[M].北京:中国宇航出版社,2011:115-117.[7]刘祥松,蔡龙.核主泵叶轮型线测量判定方法[J].水泵技术,2013(6):14-18. LIU Xiangsong, CAI Long. Measurement and certification method for impeller profile of nuclear main pump[J]. Pump technology, 2013(6):14-18.(in Chinese)[8]刘祥松,卜延鹏,邱国帆,等.1 000 MW核主泵导叶体型线检测新方法[J].排灌机械工程学报,2014,32(11):937-942. LIU Xiangsong, BU Yanpeng, QIU Guofan, et al. New method for measuring vane profile of diffuser of 1 000 MW reactor coolant pump[J]. Journal of drainage and irrigation machinery engineering, 2014, 32(11): 937-942.(in Chinese)[9]GB/T 9239.1—2006 振动机械 恒态(刚性)转子平衡品质要求 第1部分:规范与平衡允许的检验[S].北京:中国标准出版社,2007.[10]GB/T 11348.2—2012 机械振动 在旋转轴上测量评价机器的振动 第2部分:功率大于50 MW,额定工作转速1 500 r/min、1 800 r/min、3 000 r/min、3 600 r/min陆地安装的汽轮机和发电机[S]. 北京:中国标准出版社,2012.[11]李彬,夏虹. 基于最优小波基的主泵裂纹转子特征识研究[J]. 振动与冲击,2014,33(21): 207-212. LI Bin, XIA Hong. Feature recognition of cracked rotor of RCP based on optimal wavelet basis [J]. Journal of vibration and shock, 2014, 33(21): 207-212.(in Chinese)[12]杨璋. 三轴承支承主泵振动特性研究[J]. 核动力工程,2015,36(3):84-87. YANG Zhang. Study on vibration characteristics of three bearing supporting main coolant pump [J]. Nuclear power engineering, 2015, 36(3): 84-87.(in Chinese)[13]赵振宇,高培. 岭澳核电站主泵动平衡[J]. 中国设备工程,2011(4):32-34. ZHAO Zhenyu, GAO Pei. Dynamic balancing of main pump of Lingau nuclear power station [J]. China plant engineering, 2011(4): 32-34.(in Chinese)[14]廖详令. 方家山核电厂主泵轴密封水系统运行分析[J]. 核动力工程,2015,36(S1): 78-81. LIAO Xiangling. Analysis of operation of reactor coolant pump shaft seal system in Fangjiashan NPP [J]. Nuclear power engineering, 2015, 36(S1): 78-81.(in Chinese)[15]杜鹏程,王川,袁潮潋,等. 主泵机械密封返修处理与优化[J]. 中国核电,2015,8(4):331-334. DU Pengcheng, WANG Chuan, YUAN Chaolian, et al. Repair and modification of RCP mechanical seal [J]. China nuclear power, 2015, 8(4): 331-334.(in Chinese)[16]张青雷,高孟雪,徐华,等. 考虑激振频率的可倾瓦推力轴承动特性理论与试验研究[J]. 机械工程学报,2014,50(23):50-58. ZHANG Qinglei, GAO Mengxue, XU Hua, et al. Theoretical and experimental study on the dynamic characte-ristics of tilting pad thrust bearing considering excitation frequency [J]. Journal of mechanical engineering, 2014, 50(23): 50-58.(in Chinese)[17]冯晓东,蔡龙,杨立峰,等. 1 000 MW反应堆冷却剂泵一体化供油泵的试验研究[J]. 水泵技术,2015(1): 4-10. FENG Xiaodong, CAI Long, YANG Lifeng, et al. Experimental study of the lobe-oil pump integrated for 1 000 MW reactor coolant circulating pump[J]. Pump technology, 2015(1): 4-10.(in Chinese)[18]冯晓东,蔡龙,吴大转,等. 300 MW轴封型核主泵循环油泵的数值模拟与试验研究[J]. 排灌机械工程学报,2015,33(5):391-396. FENG Xiaodong, CAI Long, WU Dazhuan, et al. Numerical simulation and experiment of integrated oil circulating pump for 300 MW shaft seals type RCP[J]. Journal of drainage and irrigation machinery engineering, 2015, 33(5):391-396.(in Chinese)