|
|
|
| Effects of structure parameters of scavenge sump on oil/air two-phase flow in bearing chamber |
| 1. College of Energy and Power Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing, Jiangsu 210016, China; 2. Jiangsu Province Key Laboratory of Aerospace Power System, Nanjing University of Aeronautics and Astronautics, Nanjing, Jiangsu 210016, China; 3. Ministry of Industry and Information Key Laboratory of Thermal Environment and Structure in Aero Engine, Nanjing University of Aeronautics and Astronautics, Nanjing, Jiangsu 210016, China |
|
|
|
|
Abstract To solve the difficulty of oil scavenge and cooling in bearing chamber of aero-engine, the scavenge sump was improved. The effects of the sump structure parameters on oil residence volume fraction (φR), scavenge ratio and convection heat transfer coefficient of the wall were investigated by the volume of fluid (VOF) method in CFD software. The numerical simulation shows that with the increasing of shaft speed, the oil scavenge ability of bearing chamber is decreased, and the heat transfer ability of the wall surface is increased gradually. With the increasing of sump width, φR is decreased with latter rising, while the scavenge ratio is increased monotonously. φR is decreased， and scavenge ratio tends to increase with the increasing of sump depth. Compared with the basic model, the narrow sump (w=1.0) and the shallow sump (h=1) can effectively improve the heat transfer capacity of the wall surface. Appropriate adjustment of the sump position can improve the oil scavenge and heat transfer performance.
|
|
Received: 06 November 2018
|
|
|
|
| ［1］ |
GORSE P, BUSAM S, DULLENKOPF K. Influence of operating condition and geometry on the oil film thickness in aeroengine bearing chambers［J］. Journal of Engineering for Gas Turbines and Power-Transactions of the ASME,2006, 128(1): 103-110.
|
| ［2］ |
CHEN G D, SUN H C, WANG J. Research into confi-guration and flow of wall oil film in bearing chamber based on droplet size distribution［J］. Chinese Journal of Aeronautics, 2011, 24(3): 355-362.
|
| ［3］ |
ZHAO J Y, LIU Z X. Numerical and experimental study for unsteady oil film thickness of the rotating cylinder chamber wall［J］. Journal of Engineering for Gas Turbines and Power-Transactions of the ASME, 2015, 137 (12): 122501.
|
| ［4］ |
任国哲, 刘振侠, 赵静宇, 等. 基于DPM与VOF方法轴承腔内滑油瞬态特性对比［J］. 航空计算技术, 2016, 46(1): 11-15.
|
|
REN G Z, LIU Z X, ZHAO J Y, et al. Motion of wall oil film with consideration of oil-gas coupled heat and mass transfer in bearing chamber［J］. Aeronautical Computing Technique, 2016, 46(1): 11-15. (in Chinese)
|
| ［5］ |
胡剑平, 任国哲, 易军, 等.轴承腔内壁与油膜换热的数值模拟与试验［J］. 航空学报, 2017, 38(9): 521013.
|
|
HU J P, REN G Z, YI J, et al. Numerical simulation and experiment for heat transfer between oil film and inner wall of bearing chamber［J］. Acta Aeronautica et Astronautica Sinica, 2017, 38(9): 521013. (in Chinese)
|
| ［6］ |
FARRALL M, HIBBERD S, SIMMONS K. The effect of initial injection conditions on the oil droplet motion in a simplified bearing chamber［J］. Journal of Enginee-ring for Gas Turbines and Power-Transactions of the ASME, 2008, 130(1): 012501.
|
| ［7］ |
CHANDRA B, SIMMONS K, PICKERING S, et al. Factors affecting oil removal from an aeroengine bearing chamber［C］∥Proceedings of ASME Turbo Expo 2010: Power for Land, Sea, and Air. Glasgow, UK：［s.n.］,2010:GT2010-22631.
|
| ［8］ |
CHANDRA B, SIMMONS K, PICKERING S, et al. Study of gas／liquid behavior within an aeroengine bea-ring chamber［J］. Journal of Engineering for Gas Turbines and Power-Transactions of the ASME, 2013, 135(5): 051201.
|
| ［9］ |
ADENIYI A A, MORVAN H P, SIMMONS K A. A transient CFD simulation of the flow in a test rig of an aeroengine bearing chamber［C］∥Proceedings of ASME Turbo Expo 2014: Turbine Technical Conference and Exposition. Düsseldorf, Germany: ［s.n.］,2014: GT2014-26399.
|
| ［10］ |
SIMMONS K, CHANDRA B. Experimental investigation into the performance of shallow aeroengine off-takes［C］∥Proceedings of ASME Turbo Expo 2014: Turbine Technical Conference and Exposition. Dusseldorf, Germany:［s.n.］,2014: GT2014-26132.
|
| ［11］ |
CHANDRA B, COLLICOTT S H, MUNSON J H. Sca-venge flow in a bearing chamber with tangential sump off-take［J］. Journal of Engineering for Gas Turbines and Power-Transactions of the ASME, 2013, 135(3): 032503.
|
| ［12］ |
KURZ W, DULLENKOPF K, BAUER H J. Influences on the oil split between the offtakes of an aero-engine bearing chamber［C］∥Proceedings of ASME Turbo Expo 2012: Turbine Technical Conference and Exposition. Copenhagen, Denmark: ［s.n.］,2012: GT2012-69412.
|
| ［13］ |
KURZ W, DULLENKOPF K, BAUER H J. Capacitive film thickness measurements in a ventless aero-engine bearing chamber-influence of operating conditions and offtake design［J］. Journal of Engineering for Gas Turbines and Power-Transactions of the ASME, 2013, 135(11): 112504.
|
| ［14］ |
ADENIYI A A, CHANDRA B, SIMMONS K. Computational study of a customised shallow-sump aero-engine bearing chamber with inserts to improve oil residence volume ［C］∥Proceedings of ASME Turbo Expo 2012: Turbine Technical Conference and Exposition. USA: ［s.n.］,2017: GT2017-64410.
|
| ［15］ |
陈国定, 王涛, 刘曼利, 等. 轴承腔两相流动流型特征参数及鲁棒性分析［J］. 西北工业大学学报, 2012, 30(2): 155-159.
|
|
CHEN G D, WANG T, LIU M L, et al. Exploring how to realize accurate and efficient lubrication design and heat transfer analysis for oil／air two-phase flow in bea-ring chamber［J］. Journal of Northwestern Polytechnical University, 2012, 30(2): 155-159. (in Chinese)
|
|
|
|
2019, Vol. 40 
