摘要 采用流体体积-喷雾单向耦合(VOF-spray one way coupling)分析方法,在不同喷射压力下对缸内直喷汽油机(GDI)圆形和椭圆喷孔的内部流通特性和喷雾撞壁特性进行了模拟仿真研究.结果表明:同等压力条件下,椭圆喷孔出口处异辛烷质量流量大于圆形喷孔,当喷射压力为15.0 MPa时,椭圆喷孔长短轴比为4的椭圆喷孔E2中异辛烷质量流量要比圆形喷孔大3.54%;在喷雾贯穿阶段,由于椭圆喷雾贯穿距离始终小于圆形喷雾,导致椭圆喷雾撞击壁面的时间延迟,当喷射压力为6.0 MPa时,椭圆喷孔E2的喷雾撞壁时间较圆形喷雾推迟0.14 ms;喷雾撞击壁面后,圆形喷雾的铺展半径和卷吸高度都要大于椭圆喷雾,这是因为圆形喷雾速度快,喷雾动量大,促进了喷雾的飞溅和反弹,但这种差异随着喷射压力的提高而减小.
Abstract:The internal flow and spraywall impingement characteristics of circular and elliptical GDI orifices were simulated by the VOFspray one way coupling method under different injection pressures. The results show that the mass flow rate of isooctane at the outlet of elliptical orifice is larger than that of circular orifice, and the mass flow rate of isooctane in elliptical orifice E2 with the aspect ratio of 4 is 3.54% larger than that of circular orifice under the injection pressure of 15.0 MPa. In the spray penetration stage, the spray penetration of elliptical orifice is always smaller than that of circular orifice, which delays the time when the spray impacts the wall. Under the injection pressure of 6.0 MPa, compared with the circular orifice, the spray impingement time of the elliptical orifice E2 is delayed by 0.14 ms. The impinged spray radius width and height width of the circular orifice are larger than those of the elliptical orifices after the impingement. This is because the circular spray has larger momentum, which promotes the splash and rebound of the impinged spray, while the difference between circular and elliptical orifices is decreased with the increasing of injection pressure.
DISTASO E, AMIRANTE R, TAMBURRANO P, et al. Understanding the role of soot oxidation in gasoline combustion: a numerical study on the effects of oxygen enrichment on particulate mass and number emissions in a sparkignition engine[J]. Energy Conversion and Management, 2019, 184:24-39.
[2]
LIU Y, PEI Y Q, WANG C X, et al. Characteristics of the deposited fuel liquid film when GDI spray impacts viscous oil film[J]. Energy, doi: 10.1016/j.energy.2019.116011.
WANG Y H, YANG S C, LI B, et al. Experimental on impingement spray characteristics of multihole injector in gasoline direct injection engine[J]. Journal of Jiangsu University(Natural Science Edition),2013,34(4):390-394. (in Chinese)
QIAN D C, DUAN J Q, LIU Y D, et al. Analysis and optimization on injection pressure influence on wall wetting of GDI engine[J]. Small Internal Combustion Engine and Vehicle Technique, 2017,46(1):22-27. (in Chinese)
[5]
ZHOU Z F, MURAD S H M, TIAN J M, et al. Experimental investigation on heat transfer of npentane spray impingement on piston surface[J]. Applied Thermal Engineering, 2018,138:197-206.
[6]
LUO H L, NISHIDA K, UCHITOMI S, et al. Microscopic behavior of spray droplets under flatwall impinging condition[J]. Fuel, 2018, 219:467-476.
XU B, PEI Y Q, QIN J, et al. Experimental study on oil film characteristics of direct injection gasoline engine spray wall impingements[J].Chinese Internal Combustion Engine Engineering, 2019, 40(5): 38-45.(in Chinese)
KANG C, GAO K K, ZHANG Y C. Experimental study on pneumatic atomizing nozzle based on shear effect[J]. Journal of Drainage and Irrigation Machinery Engineering, 2022, 40(3):270-275.(in Chinese)
PEI N, YANG H, LIU L S, et al. Effect of orifice structure on spray characteristics of double swirl effervescent atomizer[J]. Fluid Machinery, 2021,49(9):1-5,12.(in Chinese)
[10]
YU S H, YIN B F, DENG W X, et al. An experimental comparison of the elliptical and circular nozzles spray and mixing characteristics under different injection pressures[J]. Fuel, 2019, 236:1474-1482.
[11]
MORAD M R, KHOSROBEYGI H. Penetration of elliptical liquid jets in lowspeed crossflow[J]. Journal of Fluids Engineering, 2019, 141(1):530-537.
[12]
WAGER D. The influence of elliptical nozzle holes on mixing and combustion in direct injection natural gas engines[D]. Toronto, CAN: University of Toronto, 2008.
[13]
AMINI G, DOLATABADI A. Axisswitching and breakup of lowspeed elliptic liquid jets[J]. International Journal of Multiphase Flow, 2012, 42:96-103.
[14]
SAHA K, QUAN S P, BATTISTONI M, et al. Coupled Eulerian internal nozzle flow and Lagrangian spray simulations for GDI systems[C]∥SAE Technical Paper Series. Michigan, USA: Sae International, doi: 10.4271/2017-01-0834.
[15]
QUAN S P, SENECAL P K, POMRANING E, et al. A oneway coupled volume of fluid and EulerianLagrangian method for simulating sprays[C]∥Proceedings of the ASME 2016 Internal Combustion Engine Fall Technical Conference. Greenville, USA:[s.n.], 2016:1-8.
[16]
SAHA K, SOM S, BATTISTONI M. Investigation of homogeneous relaxation model parameters and their implications for gasoline injectors[J]. Atomization and Sprays, 2017, 27(4):345-365.
[17]
WINKLHOFER E, KULL E, KELZ E, et al. Comprehensive hydraulic and flow field documentation in model throttle experiments under cavitation conditions[C]∥Proceedings of the ILASSEurope 2001.[S.l.]: International Conference on Liquid Atomization and Spray Systems, 2001:574-579.