|
|
|
| Numerical prediction of transient discharge coefficient in orifice flow meter |
| Li Zhifeng1,2,Wu Peng1,2,Wu Dazhuan1,2,Dai Weiping1,2,Wang Leqin1,2 |
| (1.Institute of Process Equipment,Zhejiang University,Hangzhou,Zhejiang 310027,China; 2.Engineering Research Center of High Pressure Process Equipment and Safety,Ministry of Education,Hangzhou,Zhejiang 310027,China) |
|
|
|
|
Abstract To study the characteristics of the orifice flow meter when measuring linear accelerating flow rate,taking the curves of the transient discharge coefficient(C) as the study object,the computational fluid dynamics(CFD) method was used to simulate the C and the evolutions of the corresponding flow field.The transient turbulent flow was described by the Realizable detached eddy simulation(DES).For comparative analysis,the accelerating process was discretized to separate steady-state conditions at different points of flow rate.The Realizable k-ε model was chosen as the steady-state turbulent closure.The error between curves of present steady discharge coefficient(C0) and the ISO data is less than 3%,so the current calculation results is validated.Comparison of discharge coefficients between flow acceleration process and steady-state condition was performed.Comparison results show that the transient C curve increases from 0 to a constant value gradually and the steady C0 remained in the vicinity of 0.6.The discharge coefficient together with the evolutions of velocity and pressure field were combined to further analysis the internal flow mechanisms.Reasons of deviation between transient and steady discharge coefficients are that the vortex of the acceleration state lags behind the steady-state conditions,so the pressure energy was not able to transform into the kinetic energy at the early process within a short distance.Contents of current study can serve as the reference of the instantaneous flow measurements.
|
|
Received: 15 December 2010
Published: 30 July 2011
|
|
|
|
| [1]Tsnkamoto H, Ohashi H. Transient characteristics of acentrifugal pump during starting period [J]. Journal ofFluids Engineering, 1982,104( 1 ) : 6 - 13.[2]Li Zhifeng, Peng,Wu Dazhuan, et al. Experimentaland numerical study of transient flow in a centrifugal pump during startup[ J]. Journal of Mechanical Science and Technology ,2011,25 ( 3 ) :749 - 757.[3]李志峰，吴大转，王乐勤 等.离心泵启动过程瞬态特性的试验[J].排灌机械工程学报,2010,28(5):389-393.[4]吴大转，王乐勤，胡征宇.离心泵快速启动过程外部特性的试验研究[J].工程热物理学报,2006,27(1):68-70.[5]Lefebvre P J, Durgin W W. A transient eleetromagnetie flowmeter and calibration facility [ J ]. Journal of Fluids Engineerinz, 1990,112 ( 1 ) : 12 - 15.[6]陈家庆，王波，吴波，等.标准孔板流量计内部流场的CFD数值模拟[J].实验流体力学,2008,22(2):52-55.[7]Kumar P,Michael W M B. A CFD study of low pressure wet gas metering using slotted orifice meters [ J ]. Flow Measurement and Instrumentation, 2011 , 22 ( 1 ) : 33 - 42.[8]Singh R K,Singh S N, Seshadri V. CH) prediction of the effects of the upstream elbow fittings on the perfor-manee of cone flowmeters [J]. Flow Measurement and Instrumentation,2010,21 (2) :88 -97.[9]Washio S, Takahashi S, Yu Y, et al. Study of unsteady orifice flow characteristics in hydraulic oil Iines[J ]. Journal of Fluids Engineering, 1996, 118 ( 4 ) : 743 - 748.[10]中国国家质量监督枪验检疫总局 中国国家标准化管理委员会.GB/T2624 2-2006川安装在圆形战面管道中的差太坏装置测量满管流体流量第2部分:孔板[S].北京:中国标准出版社,2007.. |
|
|
|
