|
|
|
| Effect of swept blade on hump and cavitation characteristics of axial flow pump |
| LIU Zhu-Qing1, XIAO Ruo-Fu1, Lv Teng-Fei 1, LI Shu-Lin2 |
(1. College of Water Resources and Civil Engineering, China Agricultural University, Beijing 100083,China; 2. Aviation Key Laboratory of Science and Technology on Aero Electromechanical System Integration,Nanjing, Jiangsu 211106, China) |
|
|
|
|
Abstract A swept blade was designed based on changing the stacking line in the meridional plane of an axial flow pump impeller. The high speed fuel axial flow pumps, with swept blades and datum blades respectively, were simulated in the overall operation by the code of computational fluid dynamics (CFD) and the overall efficiency and pump head performance curves were obtained. Using the full cavitation model, the cavitation performances of pumps were predicted under the designed point condition and near stall point condition to investigate the effects of swept blade on the cavitation performance and distribution of pressure on blade surfaces of an axial flow pump. According to the numerical results, the swept blade changes the hump characteristic of the axial flow pump, controls the onset and growth of the secondary flows, and recovers the lowenergy fluid on the endwalls. Therefore, the stability of operation in the hump zones is improved. Near stall point condition, the swept blade improves the cavitation characteristic of the pump, changes the pressure distribution on the impeller inlet, and avoids the separated flow on the endwalls. While under the design point condition, the swept blade reduces the cavitation characteristic, the blade surface pressure distribution also presents the pressure difference of the datum blade is higher than the swept blade, resulting in the ability of doing work of the former is better than the latter.
|
|
Received: 05 November 2011
Published: 10 April 2012
|
|
|
|
| ［1］Shi Weidong, Zhang Desheng, Guan Xingfan. Numerical and experimental investigation of highefficiency axialflow pump［J］. Chinese Journal of Mechanical Engineering, 2010,23(1): 38-44［2］Zhang Desheng, Shi Weidong, Chen Bin, et al. Unsteady flow analysis and experimental investigation of axialflow pump［J］. Journal of Hydrodynamics, Ser B, 2010, 22(1): 35-43.［3］杨正军,王福军,刘竹青,等.基于CFD的轴流泵空化特性预测［J］.排灌机械工程学报,2011,29(1):11-15.Yang Zhengjun, Wang Fujun, Liu Zhuqing, et al. Prediction of cavitation performance of axialflow pump based on CFD［J］. Journal of Drainage and Irrigation Machinery Engineering, 2011,29(1):11-15. (in Chinese)［4］毛明明,宋彦萍,王仲奇. 跨声速动叶弯和掠对非定常气动负荷的影响［J］.工程热物理学报,2010, 31(10):1663-1666.Mao Mingming, Song Yanping, Wang Zhongqi. Effect of bowed and swept rotors on unsteady aerodynamic loading in a transonic compressor［J］. Journal of Engineering Thermophysics, 2010, 31(10):1663-1666. (in Chinese)［5］McNulty G Scott, Decker John J, Beacher Brent F, et al. The impact of forward swept rotors on tip clearance flows in subsonic axial compressors［J］. Journal of Turbomachinery, 2004,126(4): 445-454.［6］杨敏官,姬凯,李忠. 轴流泵叶轮内空化流动的数值计算［J］.农业机械学报,2010,41(S1):10-14.Yang Minguan, Ji Kai, Li Zhong. Numerical calculation of cavitating flow in impeller of axialflow pump［J］. Transactions of the Chinese Society for Agricultural Machinery, 2010,41 (S1):10-14. (in Chinese)［7］Okita K, Ugajin H, Matsumoto Y. Numerical analysis of the influence of the tip clearance flows on the unsteady cavitating flows in a threedimensional inducer［J］. Journal of Hydrodynamics, Ser B, 2009,21(1): 34-40.［8］刘仲祥. 叶片的弯扭对轴流泵空化抑制的研究［D］. 哈尔滨:哈尔滨工程大学动力与能源工程学院,2005.［9］Vad J. Aerodynamic effects of blade sweep and skew in lowspeed axial flow rotors at the design flow rate: An overview［J］. Journal of Power and Energy, 2008,222(1): 69-85.［10］Zhu Fang, Jin Donghai, Gui Xingmin. Corner flow control in high throughflow axial commercial fan／booster using blade 3D optimization［J］. Journal of Thermal Science, 2012,21(1): 32-41. |
|
|
|
