|
|
|
| Turbulent flows in tubular pump and fluidstructure interaction characteristics of impeller |
| (1.College of Water Resources ＆ Civil Engineering, China Agricultural University, Beijing 100083, China; 2.College of Energy and Electric, Hohai University, Nanjing, Jiangsu 210098, China; 3.State Key Laboratory of Hydroscience and Engineering, Tsinghua University, Beijing 100084, China) |
|
|
|
|
Abstract The RNG k-ε turbulence model and the Ansys Workbench software were used to numerically investigate internal flows in a frontpositioned shaft tubular pump and fluidstructure interaction in its impeller. The simulated performances under different operation conditions are consistent with experimental data.Even though the calculated head is higher and the efficiency is lower than the experimental data, their errors are less than 10%. The velocity and pressure of fluid are uniformly distributed in the whole passage of the pump except in the discharge passage. The spiral streamlines in the front of the discharge passage show that the fluid has a residual velocity circulation after it leaves the vaned diffuser. At the design flow rate, a minimum pressure is seen on the suction surface of blade near the blade leading edge, where cavitation will be apt to occur. In addition, a static structural analysis on the impeller was carried out based on oneway fluidstructure coupling method and the stress and deformation of blades were predicted under different operating conditions. The results show that at the design flow rate, there is a maximal equivalent stress on the pressure surface of blade but at the junction of blade and hub. The total deformation of blade increases with radius, and there is a maximum deformation near the impeller tip. The calculated results will provide a reference for optimization design of tubular pumps.
|
|
Received: 24 December 2012
Published: 31 May 2013
|
|
|
|
| ［1］Zhu Honggeng, Zhang Rentian, Yao Linbi, et al. Numerical analysis of shaft tubular pumping systems［C］／／Proceedings of the 2011 International Conference on Computer Distributed Control and Intelligent Environmental Monitoring. Changsha:［s.n.］,2011: 491-495.［2］肖玉平,郑源,江如汉,等. 竖井式贯流泵装置的数值模拟与优化［J］. 水电能源科学, 2010, 28(2): 143-145.Xiao Yuping, Zheng Yuan, Jiang Ruhan, et al, Numerical simulation and optimization of shaft tubular pump device［J］. Water Resources and Power, 2010, 28(2): 143-145. (in Chinese)［3］金燕, 刘超, 汤方平. 后置灯泡贯流泵三维紊流计算［J］. 机械工程学报, 2010, 46(22): 167-174.Jin Yan, Liu Chao, Tang Fangping. 3D numerical simulation of turbulent flow in postpositional bulb tubular pump［J］. Journal of Mechanical Engineering, 2010, 46(22): 167-174. (in Chinese)［4］刘君, 郑源, 周大庆, 等. 前、后置竖井贯流泵装置基本流态分析［J］. 农业机械学报, 2010, 41(S1): 32-38.Liu Jun, Zheng Yuan, Zhou Daqing, et al. Analysis of basic flow pattern in shaft frontpositioned and shaft rearpositioned tubular pump systems［J］. Transactions of the Chinese Society for Agricultural Machinery, 2010, 41(S1): 32-38. (in Chinese)［5］郑小波, 罗兴琦, 邬海军. 基于CFD分析的轴流式转轮叶片刚强度分析［J］. 水力发电学报, 2006, 25(5):121-124.Zheng Xiaobo, Luo Xingqi, Wu Haijun. Rigidity／strength analysis of the axial flow blades based on CFD［J］. Journal of Hydroelectric Engineering, 2006, 25(5): 121-124. (in Chinese)［6］孔繁余, 王婷, 王文廷，等. 基于流固耦合的高温泵叶轮应力有限元分析［J］. 江苏大学学报: 自然科学版, 2012, 33(3): 269-273.Kong Fanyu, Wang Ting, Wang Wenting, et al. Finite element analysis of high temperature pump impeller stress based on fluidsolid coupling［J］. Journal of Jiangsu University: Natural Science Edition, 2012, 33(3): 269-273. (in Chinese)［7］王洋, 王洪玉, 张翔, 等. 基于流固耦合理论的离心泵冲压焊接叶轮强度分析［J］. 农业工程学报, 2011, 27(3): 131-136.Wang Yang, Wang Hongyu, Zhang Xiang, et al. Strength analysis on stamping and welding impeller in centrifugal pump based on fluidstructure interaction theorem［J］. Transactions of the CSAE, 2011, 27(3): 111-114. (in Chinese)［8］赵薇. 大型水轮机组流固耦合特性研究［D］. 北京: 中国农业大学水利与土木工程学院, 2008.［9］Wang Xin, Luo Shaoze. Vibration analysis of large bulb tubular pumping station considering flowstructure interaction［C］／／Proceedings of the Power and Engineering Conference. Chengdu:［s.n.］, 2010.［10］Wang Wenquan, He Xiaoqiao, Zhang Lixiang, et al. Strongly coupled simulation of fluidstructure interaction in a Francis hydroturbine［J］. International Journal for Numerical Methods in Fluids, 2009, 60(5): 515-538.［11］Münch C, Ausoni P, Braun O, et al. Fluidstructure coupling for an oscillating hydrofoil［J］. Journal of Fluids and Structures, 2010, 26(6): 1018-1033.［12］Ahmadi A, Keramat A. Investigation of fluidstructure interaction with various types of junction coupling［J］. Journal of Fluids and Structures, 2010,26(7／8): 1123-1141.［13］Campbell R L. Fluidstructure interaction and inverse design simulations for flexible turbomachinery ［D］. The Pennsylvania State: College of Engineering, The Pennsylvania State University, 2010. |
|
|
|
