|
|
|
| Numerical investigation of cavitating flows in bulb tubular pump and its performance prediction |
| TANG Xue-Lin, HUANG Wei, WANG Fu-Jun, WU Yu-Lin, LIU Zhu-Qing |
| (1.College of Water Resources ＆ Civil Engineering, China Agricultural University, Beijing 100083, China; 2.State Key Laboratory of Hydroscience and Engineering, Tsinghua University, Beijing 100084, China) |
|
|
|
|
Abstract Under the design operating condition, the RNG k-ε turbulence model and the full cavitation model were employed to investigate cavitating flows in a bulb tubular pump model with lowhead and predict its cavitation performance curve by using Fluent. The cavitating flow patterns in the pump under six operating conditions, where the cavitation inception, 3% head drop point and severe cavitation condition were included, were compared and analyzed. The static pressure and vapor volume fraction contours on the suction side of blade of the impeller and the fraction distributions in various planes located at different axial positions were obtained under different available NPSH. It was showed that a cavity occurs in the suction side of blade immediately behind the blade leading edge initially at a constant flow rate, and then it expands along the suction side with lowered available NPSH; such a cavity expansion affects the pump performance eventually. The onethird net crosssectional area of flow passages at the Z=-20 mm axial location has been occupied by the vapor with more than 10% volume fraction at the 0.81 m available NPSH, causing a serious blockage effect in the impeller passages. All the predicted results might be helpful in hydraulic and structural optimization for the bulb tubular pump in future.
|
|
Received: 16 September 2012
Published: 31 March 2013
|
|
|
|
| ［1］Zhang Desheng, Shi Weidong, Chen Bin, et al. Numerical simulation and experiment of tubular pump device model［C］／／Proceedings of the International Conference on Computational Intelligence and Software Engineering, 2009.［2］Zhu Honggeng, Zhang Rentian, Yao Linbi,et al.Numerical analysis of shaft tubular pumping systems［C］／／Proceedings of the 2011 International Conference on Computer Distributed Control and Intelligent and Environmental Monitoring.Changsha:［s.n.］,2011.［3］Vedanth Srinivasan, Abraham J Salazar, Kozo Saito. Numerical simulation of cavitation dynamics using a cavitation induced momentum deft(CIMD) correction approach［J］. Applied Mathematical Modelling, 2009, 33(3):1529-1559.［4］Wu Lei. Numerical simulations of cavitation flows ［J］. Journal of Hydrodynamics, Ser B,2003, 4(2):125.［5］Singhal A K, Athavale M M, Li Huiying, et al. Mathematical basis and validation of the full cavitation model［J］. Journal of Fluids Engineering,2002,124(3):617-624.［6］Kang Can, Yang Minguan, Wu Guangyan, et al. Cavitation analysis near blade leading edge of an axialflow pump［C］／／Proceedings of the International Conference on Measuring Technology and Mechatronics Automation. Zhangjiajie:［s.n.］,2009.［7］杨敏官,姬凯,李忠. 轴流泵叶轮内空化流动的数值计算［J］.农业机械学报, 2010,41(S1):10-14.Yang Minguan, Ji Kai, Li Zhong. Numerical study of cavitation flow inside axialflow pump impeller ［J］. Transactions of the Chinese Society for Agricultural Machinery, 2010,41(S1):10-14. (in Chinese)［8］CoutierDelgosha O, Reboud J L, Delannoy Y. Numerical simulation of the unsteady behavior of cavitation flows［J］. International Journal for Numerical Methods in Fluids, 2003,42(5):527-548.［9］Huang Jianjun, Zhang Dun, Ren Yan. Study on hydraulic characteristics of tubular pump guid vanes［C］／／Proceedings of the International Conference on Material for Renewable Energy ＆ Environment (ICMREE), 2011.［10］Masashi Fukaya, Tomoyoshi Okamura, Yoshiaki Tamura, et al. Prediction of cavitation performance of axial flow pump by using numerical cavitating flow simulation with bubble flow model［C］／／Proceedings of the Fifth International Symposium on Cavitation. Osaka,Japan:［s.n.］,2003.［11］李军,刘立军,李国军,等.离心泵叶轮内空化流动的数值预测 ［J］. 工程热物理学报,2007,28(6):948-950.Li Jun, Liu Lijun, Li Guojun, et al. Numerical prediction of cavitation inside centrifugal pump impeller ［J］.Journal of Engineering Thermophysics, 2007, 28(6):948-950. (in Chinese)［12］占梁梁.水力机械空化数值计算与试验研究［D］. 武汉:华中科技大学能源与动力工程学院,2006.［13］赵希枫. 基于CFD技术改善离心泵内部空化性能的研究［D］. 兰州:兰州理工大学流体动力与控制学院,2009. |
|
|
|
