Abstract：The design processes of pump hydraulic fixer from several aspects are presented,such as the design of system structure,the analysis of clamp′s strength,the design of hydraulic system and the principle of electric control.To ensure no leak phenomenon,the technique of groove and seal is applied in pipe connective part.The results show that hydraulic fixer strength is about 88.238 kN and the least working pressure is about 17.563 MPa under the pressure of 6.4 MPa in hydraulic cylinder.Compared with traditional flange alignment,the test results show that the fixer has no leak phenomenon,hydraulic loss on alignment part has declined about 0.156%,and the number of pump tested in the same time is 1.5 times than before,so it can greatly improve efficiency of pumps′ testing.
王洋， 吴登昊， 张翔， 杨炎财. 水泵试验台液压夹紧装置设计[J]. 排灌机械工程学报, 2009, 27(1): 19-24.
Wang Yang,Wu Denghao,Zhang Xiang,Yang Yancai. Design of hydraulic fixer in test bench of pump. Journal of Drainage and Irrigation Machinery Engin, 2009, 27(1): 19-24.
[1]刘银水,廖义德,姜静,等.阻尼器试验台架液压夹紧装置的分析设计[J].武汉理工大学学报,2007,29(7):110-113.Liu Yinshui,Liao Yide,Jiang Jing,et al.Analysis and design of the hydraulic clamp assembly in a test bench of the damper[J].Journal of Wuhan University of Techno-logy,2007,29(7):110-113.(in Chinese)[2]马继春,宁建,马良.水泵试验台快速夹紧机构的研制[J].农业装备与车辆工程,2007(2):17-19.Ma Jichun,Ning Jian,Ma Liang.Development of quick clamp device for pump testing[J].Agricultural Equipment & Vehicle Engineering,2007(2):17-19.(in Chinese)[3]Nomura M,Suzuki M,Hori M,et al.Decoupling torque control system for automotive engineer tester[J].IEEE Transactions on Industry Applications,2000,36(2):467-474.[4]Justin W R,Kazerooni H.Analysis and design of a novel hydraulic power source for mobile robots[J].IEEE Transactions on Automation Science and Engineering,2005,2(3):226-232.[5]Lee K O,Hur Y M,Kang J H,et al.Performance estimation of wipers for hydraulic cylinders and optimization of geometric design variables[J].Journal of Materials Technology,2007,187:215-219.[6]Chin J H,Sun Y H,Cheng Y M.Force computation and continuous path tracking for hydraulic parallel manipulators[J].Control Engineering Practice,2008,16:697-709.[7]Bilodeau G,Papadopoulos E.A model-based impedance control scheme for high-performance hydraulic joints[C]∥Proceedings of the 1998 IEE/RSJ Intl.Conference on Intelligent Robots and Systems Victoria,B.C,Canada:[s.n.]1998.[8]江灏.液压综合试验平台的PLC实时测控系统设计与开发[D].杭州:浙江大学,2006.[9]朱本坤.基于单片机的模糊PID恒压供水控制系统[J].排灌机械,2008,26(1):43-46.Zhu Benkun.Fuzzy-PID constant-pressure water supply system based on single chip computer[J].Drainage and Irrigation Machinery,2008,26(1):43-46.(in Chinese)[10]尤亚峰,马新华,李乔军,等.基于PLC的水泵试验台电动阀门PI控制的实现[J].排灌机械,2007,25(4):50-53.You Yafeng,Ma Xinhua,Li Qiaojun,et al.Realization of the electric valve′s PI control in pump test-bed based on PLC[J].Drainage and Irrigation Machinery,2007,25(4):50-53.(in Chinese)
