排灌机械工程学报
   首页  学报介绍  编 委 会  作者园地  征订启事  编校法规  编读往来  录用公告  广告合作   行业新闻  留  言  English 
排灌机械工程学报  2019, Vol. 37 Issue (4): 296-301    DOI: 10.3969/j.issn.1674-8530.17.0006
泵理论与技术 最新目录 | 下期目录 | 过刊浏览 | 高级检索 Previous Articles  |  Next Articles  
屏蔽泵冷却循环回路的热流耦合
周以松*,孔繁余,操瑞嘉,孙静如
江苏大学国家水泵及系统工程技术研究中心, 江苏 镇江 212013
Heat flow coupling of the cooling circulation loop on the canned-motor pump
ZHOU Yisong*,KONG Fanyu,CAO Ruijia,SUN Jingru
National Reaserch Center of Pump, Jiangsu University, Zhenjiang, Jiangsu 212013, China
 全文: PDF (3191 KB)   HTML (1 KB)   输出: BibTeX | EndNote (RIS)      背景资料
摘要 为了研究屏蔽泵冷却循环回路与泵内部温升关系,模拟计算了屏蔽电动机内部温度场与压力场的分布以及冷却循环回路中的温升,分析了冷却液与电动机定转子之间的对流换热信息.以冲压成型屏蔽泵实型样机为研究对象,利用工程仿真软件CFD,对屏蔽泵叶轮前后腔体、冷却循环回路等全流场进行热流耦合数值分析.结果表明:屏蔽套间隙内的温升在不同流量工况下温度变化较小,最大温差为0.97 ℃;额定流量工况下,轴孔径的大小对屏蔽电动机的温升影响较小.随着轴孔径的逐渐增大,电动机内的最大温度逐渐减小;在额定流量工况下,由屏蔽泵数值与理论计算两种情况的循环流量与轴孔径的关系可以得出:数值计算与理论计算两者的结果基本一致,研究结果为屏蔽泵冷却循环回路的设计提供理论依据.
服务
把本文推荐给朋友
加入我的书架
加入引用管理器
E-mail Alert
RSS
作者相关文章
周以松*
孔繁余
操瑞嘉
孙静如
关键词屏蔽泵   热流耦合   数值模拟   冷却循环   轴孔径     
Abstract: To investigate the relationship between cooling circulation loop of cannedpumps and the internal temperature rising, the distribution of temperature field and pressure field in the canned motor and the temperature rise in the cooling circulation loop were simulated and the convective heat transfer information between the coolant and the rotor was analyzed.The thermal-fluid coupling numerical analysis of the whole flow field of the impeller, the chamber and the cooling circulation circuit of the canned pump was carried out by using the engineering simulation software CFD based on the real prototype of the stampingwelding cannedmotor pump. The results show that under different working conditions, the temperature rise in the shielding gap is very small, the maximum temperature difference is only 0.97 ℃. Under the design condition, the different shaft aperture has little effect on the temperature rise of the cannedmotor. With the increase of axial aperture, the maximum temperature of cannedmotor is decreasing. Under the design condition, the relationship between cooling cycle flow and axial aperture is compared with the numerical calculation and theoretical calculation.It is concluded that the results of numerical calculation and theoretical calculation are basically the same, which provides a theoretical basis for the design of cooling cycle circuit of cannedpump.
Key wordscanned motor pump   heat flow coupling   numerical simulation   cooling cycle   axial aperture   
收稿日期: 2017-01-04;
引用本文:   
周以松*,孔繁余,操瑞嘉等. 屏蔽泵冷却循环回路的热流耦合[J]. 排灌机械工程学报, 2019, 37(4): 296-301.
ZHOU Yi-Song-*,KONG Fan-Yu,CAO Rui-Jia et al. Heat flow coupling of the cooling circulation loop on the canned-motor pump[J]. Journal of Drainage and Irrigation Machinery Engin, 2019, 37(4): 296-301.
 
[1] 钱家祥,童志成,陈文正,等. 冲压泵的特点及其应用[J].流体机械,1999,27(8):30-33.
QIAN Jiaxiang,TONG Zhicheng,CHEN Wenzheng, et al. The characteristics and application of stamping pump[J].Fluid machinery,1999,27(8):30-33.(in Chinese)
[2] 汪家琼,赵瑞杰,孔繁余,等.不锈钢冲压焊接离心泵研究现状[J].水泵技术,2015(4):11-15.
[3] WANG Jiaqiong, ZHAO Ruijie, KONG Fanyu,et al. Research status of stainless steel stamping welding centrifugal pump[J]. Pump technology, 2015(4):11-15.(in Chinese)
[4] 孔繁余,高翠兰,张旭锋,等. PBN65-40-250型屏蔽泵轴向力平衡计算及其试验[J]. 农业工程学报,2009,25(5):68-72.
KONG Fanyu,GAO Cuilan,ZHANG Xufeng,et al.Calculation and test of axial force balance of PBN 65-40-250 shield pump[J]. Transactions of the CSAE, 2009, 25(5):68-72.(in Chinese)
[5] 孔繁余,蒋万明,王文廷,等. 低温高速屏蔽泵汽蚀性能的流热耦合分析[J]. 华中科技大学学报(自然科学版),2012,40(5):24-28.
KONG Fanyu, JIANG Wanming, WANG Wenting, et al. Coupled heat and heat coupling analysis of cavitation performance of low temperature and high speed shield pump[J]. Journal of Huazhong University of Science and Technology(natural science edition), 2012,40(5):24-28.(in Chinese)
[6] 徐文峰,王者文.KQPL型屏蔽泵循环量与孔径的计算[J].通用机械制造,2012(4):90-92.
[7] XU Wenfeng, WANG Zhewen. Calculation of circulating quantity and pore size of KQPL shield pump[J]. General machinery, 2012(4):90-92.(in Chinese)
[8] 季建刚,孔繁余,孔祥花.屏蔽泵发展综述[J].水泵技术,2006(1):15-17,20.
[9] JI Jiangang, KONG Fanyu, KONG Xianghua. Development of shield pumps[J]. Pump technology, 2006(1):15-17,20.(in Chinese)
[10] 孔祥花,孔繁余,季建刚,等. 屏蔽泵能耗的计算与试验[J]. 排灌机械,2006,24(4):10-13.
KONG Xianghua, KONG Fanyu, JI Jiangang, et al. Calculation and test of energy consumption of shield pump[J]. Drainage and irrigation machinery,2006,24(4):10-13.(in Chinese)
[11] 戴锅生.传热学[M].北京:高等教育出版社,2008.
[12] 陶文铨. 数值传热学[M].2版.西安:西安交通大学出版社, 2001.
[13] 许明宇,温嘉斌,吴桂珍,等.防爆型高功率密度电机温度场与流体场综合计算[J].防爆电机,2008,43(3):30-34.
XU Mingyu,WEN Jiabin,WU Guizhen,et al.Comprehensive calculation of temperature field and fluid field of explosion-proof high power density motor[J]. Explosion-proof electric machine,2008,43(3):30-34.(in Chinese)
[14] 张晓晨,李伟力,曹君慈,等.屏蔽电动机屏蔽损耗与电机性能的计算与分析[J].哈尔滨工业大学学报,2007,39(9):1422-1426.
ZHANG Xiaochen,LI Weili,CAO Junci,et al.Calcu-lation and analysis of shielding loss and motor performance of shielded motor[J].Journal of Harbin Institute of Technology,2007,39(9):1422-1426.(in Chinese)
[15] LIAO Ningbo, YANG Ping. Numerical simulation of heat transfer at the interface of dissimilar materials[J]. International journal of numerical methods for heat & fluid flow, 2010, 20(1): 84-95.
[16] TOH K C, CHEN X Y, CHAI J C. Numerical computation of fluid flow and heat transfer in microchannels[J]. International journal of heat and mass transfer, 2002, 45(26):5133-5141.
[17] 蒋万明.对称布置型多级屏蔽泵的研究[D].镇江:江苏大学,2013.
[1] 杨从新,,张扬,*,钱晨,. 专用堆型对应的核主泵正反转流动数值模拟[J]. 排灌机械工程学报, 2019, 37(5): 381-386.
[2] 赵道利*,高诚锋,孙维鹏,郭鹏程,马薇. 泄水锥加长与主轴中心孔补水对水轮机尾水管流态的影响[J]. 排灌机械工程学报, 2019, 37(5): 413-419.
[3] 江伟*,蒋婷, 朱相源. 余热利用换热器硫酸和水蒸气耦合凝结数值模拟[J]. 排灌机械工程学报, 2019, 37(5): 420-426.
[4] 张凌峰,孙见君*,马晨波,张玉言. 一种钠冷快堆核主泵动静压导轴承间隙流体动力特性分析[J]. 排灌机械工程学报, 2019, 37(5): 427-434.
[5] 边若鹏,昝丙合,朱建勇*,何淼. 侧风对螺旋桨气动特性影响的数值模拟[J]. 排灌机械工程学报, 2019, 37(5): 435-440.
[6] 柏宇星,*,刘莹莹,孔繁余,夏斌,戴韬. 叶轮外径对混流泵作透平性能的影响[J]. 排灌机械工程学报, 2019, 37(4): 284-288.
[7] 刘坤,徐雷*,杨波,刘蕴. 外啮合斜齿轮高压泵的CFD数值模拟[J]. 排灌机械工程学报, 2019, 37(4): 307-312.
[8] 黄剑峰*,杨松,龙立焱,张立翔. 基于重叠网格的水轮机导叶尾流水动力特性数值研究[J]. 排灌机械工程学报, 2019, 37(4): 319-324.
[9] 边若鹏,昝丙合,朱建勇*,何淼. 桨距角对螺旋桨气动特性的影响[J]. 排灌机械工程学报, 2019, 37(4): 336-340.
[10] 徐胜荣,王新坤*,肖思强,樊二东. 射流脉冲三通结构参数数值模拟与优化[J]. 排灌机械工程学报, 2019, 37(3): 270-276.
[11] 李琪飞, 李光贤, 李仁年, 王仁本, 陈雨. 水泵水轮机在水轮机工况的导叶水力矩特性[J]. 排灌机械工程学报, 2019, 37(2): 130-135.
[12] 周大庆, 姜胜文, 陈会向. 液控蝶阀联动的混流泵机组启动过程数值模拟[J]. 排灌机械工程学报, 2019, 37(2): 112-117.
[13] 郭广强, 张人会, 赵万勇, 杨军虎, 黄祺. 浮潜式消防泵启动过程瞬态特性的数值模拟[J]. 排灌机械工程学报, 2019, 37(2): 118-123.
[14] 杨敬江,刘成强,陈汇龙,沈宇翔. 出口环量分布对泵诱导轮性能的影响[J]. 排灌机械工程学报, 2019, 37(1): 18-24.
[15] 陆静, 汤跃, 程俊.. 基于正交试验的斜击式水涡轮优化与分析[J]. 排灌机械工程学报, 2019, 37(1): 38-42.

江苏大学梦溪校区(镇江市梦溪园巷30号)图书馆5楼 0511-84440893 传真0511--84440033
Copyright 江苏大学杂志社 2010-2015 All Rights Reserved