Abstract:To explore pressure drop in a hydraulic capsule transportation pipeline and pressure between two moving capsules extensively, the pressure distribution in the annular gap between a capsule and the pipe, the pressure distribution between two capsules as well as the pressure drop across capsules were measured and analyzed by using two capsules(length-100 mm, diameter-60 mm, weight-750 g)in 10 cm apart at 30, 40, 50, 60 and 70 m3/h flow rates. It is shown that the pressure in each test section increases with increasing flow rate. At a certain flow rate, the pressure on the capsule body presents a minimum. The pressure drop across the second capsule is substantially higher than that across the first one. In the annular gap, the pressure is low on the pipe wall and capsule body, but is the highest in the middle of the gap. The pressure shows a decline downstream in the gap of the first capsule, further the pressure gradient in the gap of the second capsule is higher than that in the first one. Under various flow conditions, the pressure distribution between two capsules is uneven in some degree, but the maximum pressure is achieved on the pipe wall and the minimum one is nearly at the pipe centre. The pressure gradient between two capsules increases with flow rate.
[1]Ulusarslan D, Teke I. An experimental determination of pressure drops in the flow of low density spherical capsule train inside horizontal pipes[J].Experimental Thermal and Fluid Science,2006,30(3):233-241.[2]Vlasak P. An experimental investigation of capsules of anomalous shape conveyed by liquid in a pipe [J]. Powder Technology,1999,104(3):207-213.[3]Plodpradista W. Small-scale tubular linear induction motor for pneumatic capsule pipeline system[C]//Proceeding of the International Conference on Electrical Machines and Systems. Seoul, Korea:[s.n.], 2007:1528-1532.[4]O′Connell R M, Liu H, Lenau C W. Performance of pneumatic capsule pipeline freight transport system dri-ven by linear motor[J]. Journal of Transportation Engineering, 2008,134(1):50-58. [5]Ulusarslan D, Teke I. An experimental investigation of capsule velocity, concentration rate and the spacing between the capsule for spherical capsule train flow in a horizontal circular pipe [J].Powder Technology,2005,159(1):27-34.[6]Ulusarslan D. Determination of the loss coefficient of elbows in the flow of low-density spherical capsule train [J].Experimental Thermal and Fluid Science,2007,32(2):415-422.[7]Ulusarslan D.Comparison of experimental pressure gradie-nt and experimental relationships for the low density spherical capsule train with slurry flow relationships [J].Powder Technogy, 2008,185(2):170-175.[8]Teke I, Ulusarslan D.Mathematical expression of pressure gradient in the flow of spherical capsules less dense than water[J]. International Journal of Multiphase Flow,2007,33(6):658-674.[9]童学卫,李永业,孙西欢.筒装料管道水力输送试验系统设计研究[J].山西水利,2008(2):42-43. Tong Xuewei, Li Yongye, Sun Xihuan. Experimental system design on the piped hydraulic transportation of tube-contained raw material[J].Shanxi Water Resources, 2008(2):42-43.(in Chinese)[10]李永业,孙西欢,李飞,等.动边界同心环状缝隙流研究[J].农业机械学报,2012,43(3):230-234. Li Yongye,Sun Xihuan,Li Fei, et al.Cyclical flit flow of concentricity under the moving boundary condition[J].Transactions of the Chinese Society for Agricultural Machinery, 2012,43(3):230-234.(in Chinese)[11]李飞.不同径长比条件下筒装料管道水力输送水力特性试验研究[D].太原:太原理工大学水利科学与工程学院,2008.[12]孙西欢,李永业.管道车在有压管道中运动的试验研究[C]//第九届全国水动力学学术会议暨第二十二届全国水动力学研讨会,2009:416-422.[13]孙西欢,李永业.筒装料管道水力输送影响因素分析[C]//第四届全国水力学与水利信息学学术大会,2009:371-375.[14]束德方.管道车在不同直径比条件下运移的水力特性研究[D].太原:太原理工大学水利科学与工程学院,2010.[15]许飞. 筒装料管道水力输送平直管段轴向流速研究[D]. 太原:太原理工大学水利科学与工程学院,2011.