Influence on performance of submersible well pump changing clearance of wear-rings
Shi Weidong1, Gao Xiongfa1, Zhang Desheng1, Lu Weigang1, Zhang Qihua1, Zhang Xiao2
1.Research Center of Fluid Machinery Engineering and Technology, Jiangsu University, Zhenjiang, Jiangsu 212013, China; 2.Hubei Heqiang Machinery Development Co., Ltd., Ezhou, Hubei 436004, China
Abstract:The whole flow field of the submersible well pump 200QJ80-22 was numerically simulated with CFD. By comparing the calculation results with experimental results, the influence of clearance of wear-rings on the external characteristic and internal flow field was analyzed. The results of the nume-rical simulation shows that the head and efficiency of the pump decrease as the size of clearance increases. Especially, when the size of clearance reaches 0.7 mm, the decreasing becomes very obvious yet the pump power almost remains constant; when the size of the clearance reaches 1.00 mm, the efficiency decreases from the highest point of 77.2% to 68.7%, and the head of pump decreases by about 3.5 m; when the size of clearance is 0.2 mm, reverse-flow will appear in the front shroud cavity of the first stage impeller and second stage impeller and in the area between the impeller outlet and the front shroud, which has a small influence on the flow of the impeller inlet and flow field, because there is little leakage flow; reverse-flow gradually disappears when the size of clearance increases to 0.5 mm, but more leakage flow could impact on the impeller inlet, which results in the area of passage of impeller inlet decreasing, and thus seriously affecting the hydraulic performance of the pump.
[1]施卫东,张启华,陆伟刚.新型井泵水力设计及内部流动的数值模拟[J].江苏大学学报: 自然科学版,2006,27(6): 528-531. Shi Weidong,Zhang Qihua,Lu Weigang. Hydraulic design of new-type deep well pump and its flow calculation[J].Journal of Jiangsu University: Natural Science Edition,2006,27(6): 528-531.(in Chinese)[2]关醒凡.现代泵技术手册[M]. 北京: 宇航出版社,1995:11.[3]Kurokawa J, Matsumoto K, Matsui J, et al. Perfor-mance improvement and peculiar behavior of disk friction and leakage in very low specific-speed pumps [C]// Proceedings of the 20th IAHR International Symposium on Hydraulic Machinery and Systems.Charlotte, USA:[s.n.],2000.[4]刘在伦,王东伟,梁森.离心泵叶轮平衡孔液体泄漏量特性试验[J].农业机械学报,2012,43(7):84-88. Liu Zailun, Wang Dongwei, Liang Sen. Fluid leakage characteristic test on balance aperture of centrifugal pump impeller [J]. Transactions of the Chinese Society for Agricultural Machinery, 2012,43(7):84-88.(in Chinese)[5]施卫东,周岭,陆伟刚.高扬程深井离心泵的正交试验与优化设计[J].江苏大学学报: 自然科学版,2011,32(4):400-404. Shi Weidong, Zhou Ling, Lu Weigang. Orthogonal test and optimization design of high-head deep-well centrifugal pump[J].Journal of Jiangsu University: Natural Science Edition, 2011,32(4):400-404.(in Chinese)[6]Gülich J F. Disk friction losses of closed turbomachine impellers[J]. Forschung in Ingenieunvesen/Enginee-ring Research, 2003, 68: 87-95.[7]陈鱼,费振桃,蔡永雄,等.输送清水时口环间隙对离心油泵性能的影响[J].流体机械, 2006, 34(1): 1-5. Chen Yu, Fei Zhentao, Cai Yongxiong, et al. Effect of the clearance of wear-rings on the performance of centri-fugal oil pump while handling water [J]. Fluid Machi-nery,2006,34(1): 1-5.(in Chinese)[8]Baskharone E J. Primary/leakage flow interaction in a pump stage [J].Journal of Fluid Engineering,1999,121(3):133-138.[9]李文广,费振桃,蔡永雄.离心油泵叶轮口环间隙对性能的影响[J].水泵技术, 2004(5): 7-13. Li Wenguang, Fei Zhentao, Cai Yongxiong. Effect of clearance of wear-ring on the centrifugal oil pump [J]. Pump Technology, 2004(5): 7-13.(in Chinese)[10]赵伟国,孙建平.基于CFD 的离心泵口环间隙流动研究[D]. 武汉:华中科技大学能源与动力工程学院,2006: 4, 27-28, 47-49.[11]王洋,张翔.叶轮口环间隙对低比转数离心泵效率的影响[J].排灌机械,2008,26(6):27-30. Wang Yang,Zhang Xiang.Effect of clearance of impeller wear-rings on efficiency of low specific speed centrifugal pump [J].Drainage and Irrigation Machinery,2008,26(6):27-30.(in Chinese) [12]吴大转,许斌杰,武鹏,等.多级离心泵内部间隙流动与泄漏损失[J] 浙江大学学报:工学版,2011,45(8):1393-1398. Wu Dazhuan,Xu Binjie,Wu Peng, et al.Internal clea-rance flow and leakage loss in multi-stage centrifugal pump[J]. Journal of Zhejiang University: Engineering Science, 2011,45(8):1393-1398.(in Chinese)[13]Coutier-Delgosha O, Fortes Patella R, Reboud J L, et al. Experimental and numerical studies in a centrifugal pump with two-dimensional curved blades in cavitating condition[J]. Journal of Fluids Engineering, 2003, 125: 970-978.