Abstract：To improve the reliability in operation of slipper pad bearing in an axial piston pump, a flow model was proposed by using concept of height with equivalent flow resistance and by fully considering the flow features in the gap of bearing based on the flow resistance principle; then the pressure distribution was calculated by means of finite volume method. Besides, effects of squeezing, operation pressure, entrainment velocity, film thickness profile etc on the pressure distribution were analyzed. It was turned out that the dynamic and static pressures are relatively independent of each other and the squeezing effect can affect the dynamic pressure remarkably; the operation pressure can influence the pressure in the central recess of bearing directly but has little effect on the dynamic pressure. The entrainment velocity can alter the pressure profile considerably; the orientation of entrainment velocity can not only influence the maximum peak dynamic pressure but also induce a quite different pressure profile in the region with a thinner thickness in oil film, even a negative pressure can be resulted at the location with the biggest sloping angle in oil film thickness profile. The dynamic pressure is very sensitive to central oil film thickness and maximum sloping; in some degree, the pressure is more sensitive to the maximum sloping angle than to the thickness.
王亚军. 轴向柱塞泵滑靴副压力分布特性[J]. 排灌机械工程学报, 2014, 32(1): 1-5.
Wang Yajun. Pressure distribution characteristics in slipper pad bearing of axial piston pump. Journal of Drainage and Irrigation Machinery Engin, 2014, 32(1): 1-5.
[1]何必海, 孙建国, 叶志锋. 航空燃油柱塞泵滑靴静压润滑油膜计算分析[J]. 航空动力学报,2009, 24(12): 2822-2827. He Bihai, Sun Jianguo, Ye Zhifeng. Calculation and analysis on film thickness of the slippers based on hydrostatic bearing in the aeronautical fuel piston pump[J].Journal of Aerospace Power, 2009, 24(12): 2822-2827.(in Chinese)[2]何必海, 孙建国, 叶志锋. 燃油柱塞泵滑靴副和配流副油膜计算研究[J]. 航空动力学报,2010,25(6): 1437-1442. He Bihai, Sun Jianguo, Ye Zhifeng. Calculation and analysis of film thickness for slipper pair and valve plate pair in fuel piston pump[J]. Journal of Aerospace Po-wer, 2010, 25(6): 1437-1442.(in Chinese)[3]Sun Yi, Jiang Jihai, Zhou Yu. Analysis and simulation of the property of oil film of the slipper in axial piston pump[C]//Proceedings of the 2011 International Conference on Electronic and Mechanical Engineer and Information Technology, 2011: 1359-1362.[4]Nie S L, Huang G H, Li Y P. Tribological study on hydrostatic slipper bearing with annular orifice damper for water hydraulic axial piston motor[J]. Tribology International, 2006, 39(11):1342-1354. [5]Bergada J M,Haynes J M, Watton J. Leakage and groove pressure of an axial piston pump slipper with multiple lands[J]. Tribology Transactions, 2008, 51(4): 469-482.[6]Bergada J M, Watton J, Haynes J M. The hydrostatic/hydrodynamic behaviour of an axial piston pump slipper with multiple lands[J]. Mechanica, 2010, 45(4): 585-602.[7]Bergada J M, Watton J. Axial piston pump slipper ba-lance with multiple lands[C]//Proceedings of the ASME International Mechanical Engineering Congress and Exposition, 2002.[8]Bergada J M,Watton J. A direction leakage flow rate calculation method for axial pump grooved pistons and slippers, and its evaluation for a 5/95 fluid application[C]//Proceedings of the Fifth JFPS International Symposium on Fluid Power, 2002.[9]Koc E, Hooke C J. Considerations in the design of partially hydrostatic slipper bearings[J]. Tribology International, 1997, 30(11): 815-823.[10]唐国群,陈卓如,陈晶田. 液压马达滑靴副压力场的数值解及分析[J]. 机床与液压,2000(6):43-44. Tang Guoqun, Chen Zhuoru, Chen Jingtian. Numerical simulation on pressure field of hydraulic motors slipper pairs[J]. Machine Tools and Hydraulics, 2000(6):43-44.(in Chinese)[11]潘社卫,陈卓如,金朝铭. 液压马达滑靴副流场的数值模型研究[J]. 液压气动与密封, 2001(2): 21-23. Pan Shewei, Chen Zhuoru, Jin Zhaoming. Study on flow fields numerical model of hydraulic motors slipper pairs[J]. Hydraulics Pneumatics & Seals, 2001(2): 21-23.(in Chinese)[12]Pang Zhicheng, Zhai Wenjie, Sun Jingwu. The study of hydrostatic lubrication of the slipper in a high-pressure pump[J]. Tribology Transactions, 1993, 36(2): 316-320.[13]徐兵,李迎兵,张斌. 轴向柱塞泵滑靴副倾覆数值分析[J]. 机械工程学报,2010, 46(20): 161-168. Xu Bing, Li Yingbing, Zhang Bin. Numerical simulation of overturning phenomenal of axial piston pump slipper pair[J]. Journal of Mechanical Engineering, 2010,46(20): 161-168.(in Chinese)[14]李迎兵. 轴向柱塞泵滑靴副油膜特性研究[D]. 杭州:浙江大学流体传动及控制国家重点实验室,2011.[15]许耀铭. 油膜理论和液压泵和马达的摩擦副设计[M].北京:机械工业出版社,1984.
